DEVICES YOU NEED TO SET UP A NEW BATHTUB

Devices You Need to Set Up a New Bathtub

Devices You Need to Set Up a New Bathtub

Blog Article

Schedule Your Service

We've come across the article involving Installing A Bathtub listed below on the net and decided it made good sense to write about it with you over here.


How to Install a Bathtub Yourself
Setting up a bath tub isn't precisely brain surgery, however it does call for solid plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old bathtub is easily accessible, the job can relocate rapidly; if you need to open a wall surface to eliminate the old tub as well as place the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have actually certified yourself for the task and also are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed project, it is much better to take into consideration employing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This write-up will assist you mount a brand-new bathtub in your shower room if you have actually already purchased a new bathtub and also do not need to alter the plan of your previous water system pipelines.
Your devices and also material checklist ought to make up the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Planning for the Installment


    To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bath tub.
    Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
    Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.

    Removing Old Touches


    If you require to replace old faucets with new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of eliminating the existing taps can be rather problematic because of the restricted accessibility that is typically the case.
    Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
    Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

    Setting up the Bath tub


    Using both wood boards under its feet, place the tub in the called for setting. The wood boards are helpful in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
    The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub up until the level reads level.
    To set up faucets, fit all-time low of the furthest versatile faucet adapter to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
    Switch on the supply of water and also examine all joints and new pipework for leaks as well as tighten them if essential. Fill the bathtub as well as also check the overflow outlet as well as the typical electrical outlet for leakages.
    Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been made use of at the very least when as this will certainly settle it right into its last placement.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
    If you require to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in place in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous type should be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Tiling Around the Bathtub


    In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling listed below.
    You can choose from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can fracture relatively very early if you do not take into consideration this activity before securing.
    Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof adhesive as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Do you like more info about Tools You Need to Install a New Bathtub ? Give feedback down below. We will be interested to know your feelings about this article. In hopes that you come back again in the future. I beg you take the opportunity to promote this blog posting if you enjoyed it. Many thanks for your time. Please check our website back soon.




    Check It Out


    Report this page